Can I increase the water pressure in my bathroom faucet?
First, check the emergency shutoff under your sink to make sure it’s fully open. If rubber washers or seals have begun to deteriorate, you’ll also lose water pressure, so check those. Calcium and lime buildup will also cause low water pressure.
What should I do to take care of my faucets and sinks?
Even small drips can waste thousands of gallons of water, as much as 150 gallons a day! Be sure to check under sinks for moisture or small leaks. And always repair leaky faucets right away to avoid paying for wasted water, and also to avoid water damage to your fixtures and pipes. Remove and clean your faucet aerators annually to ensure an even flow of water. Make sure overflow holes on tubs and vanities are clear and open to prevent water damage to floors and ceilings.
Can I replace my two-handled faucet with a single-handle faucet?
Usually, faucet dimensions and sink openings are standard throughout the plumbing industry, so the answer is usually yes. There are a few exceptions, so check the size of the sink opening before you buy new fixtures.
How can I prevent clogged drains?
Do not rinse fats or cooking oils down the kitchen sink. Liquid fats solidify in the cold pipes and create clogs. To help prevent clogs, fit all your tubs and shower drains with a strainer that catches hair and soap chips, and clean the strainer regularly.
What causes my kitchen sink and washing machine drains to clog?
In most homes, the kitchen and laundry drains are connected. When the lint from the laundry drains meets the grease buildup from soap and food products, a nearly solid substance is formed, causing blockage. Using filters and strainers will help, but you’ll also need to get the drains snaked periodically as well.
Should I close and open the main water supply shutoff valve periodically?
Yes. You want to make sure they’re not stuck in the open position just when you have a water emergency! Do the same periodic check for the shutoff valves on your sinks, tubs, and toilets, too.
Why do I hear a vibrating noise in my pipes?
Noises can be fairly common in plumbing supply lines. If a washer in a faucet or valve is loose, you’ll hear it rattling or knocking. If the sound occurs when you open and close faucets rapidly, it generally means pipes are loose, and can be corrected by anchoring pipes more securely. If it really bothers you, you can add air chambers at the end of long pipe runs. Their installation will probably require a plumbing professional.
What can I do about a sewer line blockage?
The main culprit is tree roots, and once they’ve blocked the line, there is very little you can do. A plumbing professional can snake the line to get it as clear as possible, and then use copper sulfide products to kill the remaining vegetation. But odds are the sewer line will most likely need to be replaced.
Are caustic liquid drain openers (like Drano or Liquid Plumber) harmful to pipes?
For minor clogs, they’re fine, but never use them on a drain that is completely clogged. The caustic ingredients are trapped in your pipes, and it can severely damage them. If you can’t snake the drain yourself, contact a professional to do so. Never use caustic drain openers in a drain that has a garbage disposal.
Why doesn’t my old water heater work as well as it used to?
This is usually due to a sediment buildup in your tank. As water heaters grow older, they accumulate sediment and lime deposits. If these deposits are not removed periodically, the sediment will create a barrier between the burner and the water, greatly reducing the water heater's performance level. At least once every three months, drain water from the tank. Draining a gallon or so on a regular basis helps remove the sediment. You should also periodically inspect your water heater burner. The flame under the heater should appear blue with yellow tips. If it’s mostly yellow, or if it’s sooty under there, your flue may be clogged, which is a dangerous situation. Contact a professional to check it out. At least once every two years, have your water heater inspected by a service technician. He or she will also check the drain valve for signs of leakage, and the anode rods for corrosion.
What’s the best way to extend the life of my garbage disposal?
Always use plenty of cold water when running your disposal, and avoid overloading it. Never dispose of very hard items like bones or corn husks. And never use a caustic drain opener. You can extend the life of your hands by never using them to remove items dropped inside – use tongs instead!
What should I do if my garbage disposal stops working?
Before calling a professional, be sure to try the reset switch located on the bottom of most disposals.
What’s the best way to check for toilet leaks?
Toilet leaks can be wasteful and expensive. At least once a year, check your toilet for leaks by adding a small amount of red food coloring to the tank, and then check the toilet bowl later. If the toilet bowl water is colored red, water is seeping through from the tank. If it is leaking, you should replace the tank ball.
At what temperature can someone be scalded?
120 degrees for more than 5 minutes. 125 degrees for more than 2 minutes. 130 degrees for about 30 seconds
When I fill a container with hot water it is milky or has a sulfer odor. What causes this?
The most common cause of "milky" water is a non-toxic iron reducing bacteria. The simplest treatment available is shock-chlorination of the system. This is a surface treatment, and often requires repeated trials in heavily infected systems. The chlorination of a system requires that you follow each step explicitly to avoid an un-treated portion of the piping system from re-infecting another part.
What is the purpose of the air gap for your sink, garbage disposal, or drain?
This distance between the faucet and the top of the sink or bathtub (one inch or more) is required by plumbing codes. Without the "gap", waste water could siphon back into the drinking supply.
Is there anything I can do to remove scratches from my toilet bowl?
Yes, you can have your toilet refinished, which requires taking the toilet out, in which case you'll need a back-up restroom.
Another option is to buy porcelain patch and do it yourself. Shut off your angle valve and flush the toilet until it is almost empty. Do not turn the water back on until the patch is completely dry.
What is a pressure balancing valve and why should I install one on my shower system?
Pressure-balancing valves prevent sudden water temperature changes caused by flushing toilets or running sinks.
By adjusting to pressure changes in water coming through the hot and cold supply lines, a piston in the valve automatically opens or closes small inlet ports to maintain a balance in pressure, which in turn keeps the water flowing at an ambient temperature. It reacts instantaneously.
What causes my toilet to RUN?
You may have a bad flapper in the toilet tank or a bad fill valve. Both can allow the water to seep into the tank and will run up your utility bill.
How do you get water in the toilet tank to stop over flowing?
Turn the shut off valves under your toilet off, is there is none, or the valve is broken or you can get it to turn off, shut the water off to your entire house at the valve attached to the main house water supply, to give you time to assess the problem.
What might cause a high water bill besides leaking faucets or pipes?
Most leaks in residential plumbing systems are found in the toilet tank and result from worn parts or improper alignment of the flushing mechanism. Once the leak is stopped, your water bill will go down.